Cub-cadet 3654 Instrukcja Użytkownika

3654, 366025 HorsepowerHydrostatic Zero-TurnCommercial RidingMowerOPERATOR’S AND SERVICE MANUAL01004965.fm Page 1 Friday, March 23, 2001 9:17 AM

10Note: New tires are overinflated in order to properly seat the bead to the rim. The normal working pressure for the traction tires is 8-10 psi. The

11c. If the dimension at the front of the mowing deck is 1/8"-3/8" lower than the dimension at the rear of the deck on each side of the mowe

12the left hand side. (NOTE: Be sure the blades are parallel to the frame rails of the unit when taking paved surface to blade edge measurements.)b. I

13Note: Do not hold the key in the “Start” position for more than 10 seconds or you may damage the starter. If the engine does not start in this time,

14k. Practice mowing in straight passes. When you feel confi-dent, slowly practice mowing around obstacles such as trees.3. Parking the Mower:a. Push

15e. Remove six linchpins (See Fig. 6) (4) from the deck and (2) from the front of the mower. Remove the linchpins on the left and right rear side of

16a. Set the parking brake.b. Clean any debris from the blades. Keep blades sharp and free of build up at all times.c. Sharpen blades evenly at the or

175. Changing the Spindle Assemblya. Remove the deck cover. b. Remove the drive belts. (See 4. Chang-ing Blade Drive Belts.)c. Remove the cutter blad

18e. Pour hydraulic oil into the reservoir up to the lowest hole in the oil tank fill neck, if necessary.2. Draining Hydraulic OilUsed hydraulic oil m

19and water and rinse with clean water. Keep the contacts and cable ends clean with a wire brush and make sure the connections are tight. Coat the ter

2TABLE OF CONTENTSForeword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Safety Pre

20b. Attach the Negative (black) cable.c. Attach the rubber battery strap.5. Jump StartingWarning:Failure to use this starting procedure can cause spa

21blade clutch switch “off”, release the parking brake and try to start the engine. The engine should not start. If it does, the parking brake switch

22e.Electric PTO Clutch: This clutch operates when the engine is running, the operator is in the operator’s seat and the blade clutch switch is turned

23ground. Loosen and remove the locknut from the axle assemblyand pull the axle assembly from the caster yoke. The wheel andtwo spacer sleeves will dr

24Note: If you wish to move the mower by pushing, you must release the dynamic brak-ing. Locate the levers at the rear of the mower. Pull both levers

25rest of the hydraulic system. Fill the replacement filter with a good grade of20W-50 oil and lubricate the sealing surface. Screw the filter onto th

26opened out to the neutral position. If the mower begins to creep, adjust the Steering Levers. If the mower creeps, first determine whether it creeps

27G. Storage1.General: If your mower will not be in service for a few months, it should be stored in a dry location that is not subject to drastic ch

28e. Push the mower outdoors and start the engine. Let the engine idle until it has warmed up completely (4 to 5 min-utes).MAINTENANCE SCHEDULEA. Dail

291. Change the engine oil. (Every 25 hours under heavy duty opera-tion.)2. Clean or replace the engine’s paper air cleaner element.*3. Check the batt

3FORWARDThe Hydrostatic Zero-Turn Commercial Riding Mowers were developed to providesuperb maneuverability, mid-mount cutting capability for professio

30LUBRICATION CHARTUse a grease-gun filled with NO. 2 Multipurpose Lithium Base Grease Number of Grease Fittings DescriptionEVERY 25 HOURS3WEEKLY22421

31WIRING DIAGRAM01004965.fm Page 31 Friday, March 23, 2001 9:17 AM

EQUIPMENT TWO-YEAR LIMITED WARRANTYThis warranty is specific to the product manual it is attached to.For a complete list of products and warranties co

4SAFETY PRECAUTIONSA. General1. Read this Operator’s Manual before starting the mower. Study the controls and learn the proper sequence of operation.2

57. When filling the fuel tank, stop when the fuel reaches one inch from the top. This space is necessary for tank expansion. Do not overfill.8. Wipe

6brake; shutting off the engine and taking the key from the ignition switch.14. Never walk or stand on the discharge side of a mower with the engine r

7OPERATING INSTRUCTIONSA. Controls1.Engine Ignition and Start Switch: (See Figure 1.) Located on the instrument housing below the right side of the op

8Note: The Steering Lever will return toward neutral when released, but they should be placed in neutral by the driver. If the Drive Handles are not p

9to the left then push the seat forward or back to the desired posi-tion. Release the lever so the seat will lock in place.9.Digital Tachometer and Ho