CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
Connecting the Battery CablesCALIFORNIA PROPOSITION 65 WARNING! contain lead and lead compounds, che
Adjusting the Seat To adjust the position of the seat, pull up and hold the seat desired p
Systems Indicator MonitorBrake PedalDrive PedalDeck Lift LeverCup HolderFuel Tank CapThrottle/Choke ControlIgnition Switch ModuleParking Brake/Cruise
Deck Lift Leverthe deck lift lever is used to change the height of the cutting deck. To use, move the lever to t
Fuel Level IndicatorThe Fuel Level Indicator is located on the left side of the tank.PTO/Bl
TO AVOID SERIOUS INJURY OR DEATH• GO UP AND DOWN SLOPES, NOT ACROSS. • AVOID SUDDEN TURNS.• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.• I
Driving The TractorWARNING! Avoid sudden starts, excessive speed and sudden stops. Lightly press the brake pedal to release the parking brake.
Driving On Slopeswhere you may operate the tractor safely.WARNING! Do not mow on inclines
Engaging the PTO
Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringClean Hood/Dash LouversP PCheck Engine Oi
Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine
Remove the oil fill cap/dipstick from the oil f
Attach the hose coupler to the water port on your decks 4. Turn the water on.5.
Determine the approximate distance necessary for proper adjustment and proceed, if necessary.To raise the front of the deck, tighten (thread inwar
Leveling the Deck (Side to Side)If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as
Cutting Deck Removalposition and engage the parking brake.Lower the deck by moving the deck
Remove the cotter pin from the end of the stabilizer rod and slide the stabilizer out of the hanger bracket on the Gently slide
It may also be necessary to loosen the hex nut on the left idler pulley to get the belt off the pulley and around the belt guard.Carefully remove t
Figure 7-102. baffle and the cutting blade to act as a stabilizer. Remove the hex f
ChargingWARNING! while charging. Charge the battery in a well ventilated area and keep away from an open flame or
Problem Cause RemedyEngine fails to start 2. Throttle/C
Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the machine and in the manual(s) before attem
Component Part Number and Description
which you purchased you
Notes1133
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environment
GDOC-100223WARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty
IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Pl
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e scomplete stop wi
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a
8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a buil
Tractor Set-UpMoving The Tractor Manuallyrelief valve for occasions when it is necessary to
Komentarze do niniejszej Instrukcji