Cub Cadet 526 SWE Instrukcja Operatora Strona 1

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

Chute Clean-Out ToolThe chute clean-out tool is fastened to the top of the auger housing with a mounting clip and a cable tie at the factory. Cut the

Chute Assembly NOTE: Chutes on models with 4-Way Chute Control are controlled by the Chute Directional Control. See Fig. 4-1.The distance snow is thr

Snow thrower controls and features are described below and illustrated in Fig. 4-1. Shift LeverThe shift lever is located in the right side of the han

Auger ControlThe auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing

2-Way Chute Directional Control (if so equipped)The chute directional control is located on the left side of the dash panel.To change the direction in

Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopping the engi

MaintenanceEngineRefer to the Engine Operator’s Manual.Shave Plate and Skid ShoesThe shave plate and skid shoes on the bottom of the snow thrower are

Gear ShaftThe gear (hex) shaft should be lubricated at least once a season or after every twenty-five (25) hours of operation.Allow the engine to run

Drive ControlWhen the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Service719Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:Allow the engine to run until it is out o

Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine

20 se c t i O n 7 — se r v i c eRemove the belt from around the auger pulley, and slip the 7. belt between the support bracket and the auger pulley.

21se c t i O n 7 — se r v i c eBack out the stop bolt to increase the clearance between 6. the friction wheel disc and friction wheel. See Fig. 7-7.S

22 se c t i O n 7 — se r v i c eCarefully remove the hex nut which secures the hex shaft 5. to the snow thrower frame and lightly tap the shaft’s end

Troubleshooting823Problem Cause RemedyEngine fails to start Choke not in CHOKE position.1. Spark plug wire disconnected.2. Fuel tank empty or stale fu

Component Part Number and Description929-0071A Extension Cord, 110V954-04050 Auger Drive Belt (524 WE & 524 SWE)954-04260 Wheel Drive Belt (524

The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or the retailer from which you purc

Notes2611

27se c t i O n 11 — nO t e s

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sClearing a Clogged Discharge ChuteHand contact with the rotating impell

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

AssemblyRemove all loose parts before assembling.Handle AssemblyPlace the shift lever in the Forward-6 position1. Observe the lower rear area of the s

Insert hex rod into chute control head. Push rod as far into 2. chute control head as possible, keeping the holes in the hex rod pointing upward. See

Insert the hex rod into the pinion gear below the joystick. 6. Make sure to line up the hole in the hex rod with the arrow on the pinion gear. See Fig