Cub Cadet 945 SWE Two-Stage Snow Thrower Instrukcja Operatora

Printed In USASafe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty WARNINGREAD AND FOLLOW ALL SAFETY

AdjustmentsSkid ShoesThe snow thrower skid shoes are adjusted upward at the factory for shipping purposes. Adjust them downward prior to operating the

Make certain the entire bottom surface of skid shoes are 3. against the ground to avoid uneven wear on the skid shoes; then tighten nuts and bolts sec

Slide the spring up the cable to expose the cable coupler 2. threads and lock nut. Refer to Fig. 3-13.Adjust the lock nut as follows: If adjusting the

Snow thrower controls and features are described below and illustrated in Fig. 4-1. NOTE: For detailed information on all engine controls, refer to

Throttle ControlThe throttle control is located on the rear of the engine. It regulates the speed of the engine and will shut off the engine when move

Two-Way Chute Control™The two-way chute control is located on the left side of the dash panel and is used to control the distance of snow discharge fr

Starting The EngineAttach spark plug wire to spark plug. Make certain the 1. metal loop on the end of the spark plug wire (inside the rubber boot) is

Operating TipsNOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.WARNI

WARNING! Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a com

Checking Spark PlugWARNING! DO NOT check for spark with spark plug removed. DO NOT crank engine with spark plug removed.WARNING! If the engine has bee

To The Owner12Record Product InformationBefore setting up and operating your new equipment, please locate the model plate on the equipment and record

Auger ShaftAt least once a season, one at a time, remove all of the shear pins from the auger shaft. Spray lubricant inside the hub of each auger spi

Chute ControlThe distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Operation section for instructions

Belt ReplacementBelt Removal Preparation Remove the cotter pin which secures the upper chute 1. crank to the lower chute crank. Refer to Figure 7-1. R

Pull the brake bracket assembly towards the cable 3. guide roller and unhook the auger cable “Z” fitting. Refer to Fig. 7-5.From b4. oth sides of the

NOTE: Make sure to remove the piece of wood blocking the impeller.Check the auger drive belt adjustment. With the auger clutch lever in the disengage

Lift the friction wheel assembly out between the axle 6. shaft and the drive shaft assemblies.Remove four screws securing the friction wheel to the 7.

Off-Season StorageIf the snow thrower will not be used for 30 days or longer, the equipment needs to be stored properly. Follow storage instructions b

Troubleshooting827Problem Cause RemedyEngine fails to start Choke not in CHOKE position.1. Spark plug wire disconnected.2. Fuel tank empty or stale f

Phone (800) 965-4CUB (4282) to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual

Notes1029

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB) and the United States Environment Protection Agency (U. S. EPA) Emission Contr

(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warra

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sClearing a Clogged Discharge ChuteHand contact with the rotating impell

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Secure the upper handle and lower handle with the two wing 4. nuts and carriage bolts removed earlier. Tighten the two wing nuts already installed in

Place chute assembly onto chute base as shown in Fig. 3-5. Make sure that the chute notches engage with the spiral end of chute directional control, a

Adding FuelWARNING! Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indo