Hydrostatic Zero-TurnCommercial Riding MowerProfessional Turf EquipmentOPERATOR’S AND SERVICE MANUALMODEL20HP Enforcer 4422HP Enforcer 4823HP Enforcer
10OPERATING INSTRUCTIONSFigure. 1 Figure. 2Ignition SwitchElectric BladeClutch SwitchHour MeterEngine throttleChoke parking brakeE. General1. When Mow
112. Safety Awareness when Mowinga. Do not operate on steep slopes, those above 15 degrees (27% slope).b. Avoid turning downhill if possible, use extr
124.Electric Blade Clutch Switch: (See Figure 1.) Located on the right side of the mower beside the ignition switch. This is an “on/off” push-pull swi
13G. Initial Adjustments1. Check the fluid levels and tires:Note: These checks should be made daily, before starting the engine.a. Fuel: Using a good
145. Lubricate all fittings listed in the mainte-nance section.H. Zero Turn Break-In And Operating Pro-ceduresDANGER:Reread the “When Mowing” Safety P
15bar forward more than the left side. NOTE: If one lap bar is in the neutral position and the other is advanced, the turn side tire will not rotate a
16h. Gasoline Engine: Once the engine starts, move the choke/throttle to the detent as the engine warms.4.Operating the Mower: Operating a zero-turn-i
17MAINTENANCE ANDSERVICEWARNING:Disconnect the spark plug wires or remove the key from the ignition to prevent the engine from accidentally starting b
18f. Remove the blade.g.Figure. 7hair pinTrailing Linkhair pinsTo replace the blade reverse the above process and tighten nut to 100-120 lb ft.Note: A
195.Figure 8SpindleChanging the Spindle Assemblya. Jack up the front of the mowing deck about one foot and block it in that position.b. Make sure the
2TABLE OF CONTENTSForeword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20a. Attach the positive (red) cable.b. Attach the negative (black) cable.c. Attach the rubber battery strap.5. Jump StartingWarning:Failure to use th
21seat switch, the blade clutch switch and the electric blade clutch. Then check the seat switch, the blade clutch switch and finally the electric bla
22on the cable near the brake arm on the transaxle. If the brake is not holding, adjust the nuts so that the brake cable housing moves away from the
23MAINTENANCE SCHEDULEA. Daily Checks1. Before starting engine:a. Check the fuel level by viewing in the tank.b. Check the engine oil level.**c. Check
24.OIL CHARTApply a few drops of SAE 15W-40 engine oil, grease, or use a spray lubricant. Apply the oil to both sides of pivot points. Wipe off any ex
25Performance AdjustmentsA. High Speed Tracking AdjustmentIf mower tracks to one side with both lap bars in fully forward position:1. Check air pressu
26C. Deck Corner Ball Wheel Roller Settings1. Matching the set heights of the ball rollers on the four corners of the mower deck to the desired cut he
27F.Deck leveling Procedure1. Park the mower on a flat paved surface, engage the parking brake, shut off the engine, remove the key from the ignition
28WIRING DIAGRAMGD: 02003651
29SLOPE GAUGEDo not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could ove
3FOREWORDThe Hydrostatic Zero-Turn Riding Mower provides superb maneuverability and mid-mount cut-ting. The machine incorporates many safety features
30MAINTENANCE RECORDDATE WORK PERFORMED DATE WORK PERFORMED
Cub Cadet LLC - P.O. Box 361131, Cleveland, Ohio 44136-0019; Phone 1-877-282-8684MANUFACTURER’S LIMITED WARRANTY FOR CUB CADET COMMERCIAL ENFORCER ZER
4WARNING• The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to c
5should not be driven up or down a ramp onto a trailer or truck under power, because the unit could tip over causing serious personal injury. The uni
66. Use extra care when approaching blind cor-ners, shrubs, trees or other objects that may obscure your vision of a child or other hazard.7. Remove t
7and is contained within the positive and negative ter-minals as well as within the battery’s internal grid-work of plates and active materials.A. Exp
Part Number: 777S32598Part Number: 777S30145Part Number: 777I22444K EEP HA NDS and FE ET AW AYDANGERTO REDUCE THE RISK OF INJURY,D O N OT O PERATE MOW
9SPECIFICATIONSGENERAL INFO.Controls: Engine ignition and start switch; throttle & choke; left and right steering levers; electric blade clutch sw
Komentarze do niniejszej Instrukcji